*** Disclaimer *** O que se segue é apenas para fins informativos, i não assumimos qualquer responsabilidade pelo que você faz com esse conhecimento. i não pode ser responsabilizada por qualquer dano material ou médicos causados por esta arma. Aconselho que você verifique as leis locais. Estes tipos de armas são ilegais em algumas áreas, e eu aconselho você contra a construção de uma dessas áreas, disse. Rifles pneumáticos podem ser muito poderosos e nunca deve ser apontado para uma pessoa ou animal. Por último nunca quando se trata de pressionar-los sobre pneumática e sempre use NFS-PW pipe (como apposed DWV)
bem antes de começar devo dizer algumas coisas ...
-PVC pode ser utilizada apenas na metade ou menos da metade de classificação a pressão estampada no tubo quando gases pressurizados são usados na tubulação-I sugeriria nunca pressurização este canhão acima de 150 psi, lembre-se seu único plástico-Nunca armazenar qualquer tipo de PVC pneumático com pressão ainda nele-Sempre permitir uma completa 24 horas de PVC cola secar antes de pressurizaçãoAo construir-pneumática sempre usar de metal ou tubo de PVC (nunca ABS)-PVC é o significado sensível ao choque, se a sua queda em um disco rígido é muito provável será danificado e seria muito perigoso para pressurizar depois de danificado-PVC torna-se muito frágil abaixo de 32 graus (Fahrenheit) e é muito provável que explodir se pressionados em tais condições-Na construção de pressão pneumática avaliado tubulação deve ser sempre usado (nenhum dos que o núcleo celular ou porcaria DWV)-A parte mais importante de qualquer pneumática são as soldas PVC E eu sugiro que você leia este tutorial antes de sequer pensar em começar este.-Quando você está lidando com projéteis de alta velocidade sempre lembrar que os óculos de segurança-Sempre a certeza de sua volta parar ao fotografar qualquer tipo de rifle, pistola, arma arco, .... qualquer coisa que pode disparar alguma forma vaga de projétilE usar o bom senso!-Não use un-regulado HPA ou CO2 em um canhão PVC sempre eles são armazenados em a alta das pressões para ser seguro em PVC, mas se você tiver uma instalação devidamente regulamentados eles podem ser usados (se você diminuir a pressão sobre 100psi )
Agora para a parte boa ...
esta é a minha entrada para o lançamento é desafio, é um canhão pneumático 25MM. ele tem 2,5 metros de comprimento de um barril polegadas de diâmetro com um ferrolho mechinism personalizado, é claro que temos o escopo do sniper 3-9x40, e um 1 "válvula de sprinkler modificada como a válvula de disparo primário.
O vídeo ...
Vídeoinválido filme: http://youtube.com
lembre-se sempre usar óculos de segurança, você nunca sabe onde ou quando alguma coisa vai ricochet especialmente quando a sua viajando a 300 + FPS
Fun Fact: PVC fragmentos não podem ser captados por Raios-X (esta é uma dica de segurança não se apressar ou você vai ter um caco de PVC em você e você provavelmente não vai tirá-lo Eu não estou dizendo que você deve furtivo. um desses em sua bagagem e ir jogou a segurança do aeroporto. seria maneira de alguma maneira grande)
melhor vídeo em breve
Se você gosta deste instructable por favor registrar e votar a favor no lançamento que desafio (clicando no ícone mais próximo ao título)
Especificações detalhadas
fonte de alimentação de ar comprimido ------------------fonte de energia de pressão 100psi -----volume da câmara -------------- 45 ci (aprox.)volume de barril ------------------ 25 ci (aprox.)c / relação b -------------------------- 1,8-1 (aprox.)disparo da válvula pneumática ---------------------- válvula acionada sprinkler (a "modded sprinkler" válvula)válvula piloto ----------------------- válvula de pistola de arpreencher válvula -------------------------- feminina de desconexão rápidataxa de incêndio -------------------------- único tiro, de ferrolho--------------------------- calibre 25MM (uma polegada)velocidade do projétil ------------- desconhecido (em breve)alcance efetivo desconhecido ---------------- (em breve)O alcance máximo ------------- desconhecido (em breve)óptica --------------------------- 3-9X40MM rifleprincipal material utilizado ------ tubo de PVC
Sugiro que você faça alguma pesquisa antes de tomar este SOB PROJETO, olhar para a DIFERENTES TIPOS DE TUBO E LÁ RATINGS, COMO SOLVENTE WELD PVC (ESTE É UM MUST), como fazer corretamente DRILL E BURACOS PARA CONEXÕES DE ROSCA, digite o DAS CONDIÇÕES PVC podem ser usados e armazenados em arquivos. A maioria dessas informações está contido nessa INSTRUCTABLE MAS está ficando claro que muitos de vocês não estão lendo TODOS TI. Tenho uma sugestão FINAL CONSTRUÍDO A PNEUMÁTICO BASIC ou combustão PRIMEIRO SE UM CANHÃO BASIC NÃO SERÁ menos perigoso
PS - Não tente isso em todos SE TIVER NO senso comum ou um baixo QI
TEXTO ORIGINAL.ABAIXO COM IMAGENS.
***Disclaimer*** The following is for informational purposes only, i take no responsibility for what you do with this knowledge. i can not be held responsible for any property or medical damages caused by this weapon. i would advise you to check your local laws. These types of guns are illegal in some areas, and i would highly advise you against building one of these in said areas. Pneumatic rifles can be very powerful and should never be pointed at a person or animal. Lastly when dealing with pneumatics never over pressurize them and always use NFS-PW pipe (as apposed to DWV)
well before we begin i must state a few things...
-PVC can only be used at half or less than half the pressure rating stamped on the pipe when pressurized gases are used in the pipe
-i would suggest never pressurizing this cannon above 150 psi, remember its only plastic
-never store any type of PVC pneumatic with pressure still in it
-always allow a full 24hours for PVC glue to dry before pressurizing
-when building pneumatics always use metal or PVC pipe (never ABS)
-PVC is shock sensitive meaning if its dropped on a hard its very likely it will be damaged and it would be very dangerous to pressurize after damaged
-PVC becomes very brittle below 32 degrees (Fahrenheit) and is very likely to explode if pressured in such conditions
-when building pneumatics pressure rated pipe should always be used (none of that cell core or DWV crap)
-the most important part of any pneumatic are the PVC welds AND I HIGHLY SUGGEST YOU READ THIS TUTORIAL before you even think about starting this.
-when you are dealing with high velocity projectiles always remember you safety glasses
-always be sure of your back stop when shooting any form of rifle, pistol, gun, bow.... anything that can fire some vague form of projectile
-and use common sense!
-do not use un-regulated HPA or CO2 in a PVC cannon ever they are stored at to high of pressures to be safe in PVC, but if you have a properly regulated setup they can be used ( if you lower the pressure to about 100psi)
Now onto the good part...
this is my entry for the launch it challenge, it is a 25MM Pneumatic Cannon. it has 2.5 foot long one inch diameter barrel with a custom bolt action mechinism, of course we have the 3-9X40 sniper scope, and a 1" modified sprinkler valve as the primary firing valve.
The Video...
remember always wear safety goggles, you never know where or when something will ricochet especially when its traveling at 300+FPS
Fun Fact: PVC shards can't be picked up by X-Rays (this is a safety tip! don't rush or you'll get a PVC shard in you and you probably wont get it out. im not saying you should sneak one of these into your luggage and go threw airport security. it would be way to big any way)
better video coming soon
If you like this instructable please register and vote for it in the launch it challenge (by click the plus icon next to the title)
DETAILED SPECS
power source------------------compressed air
power source pressure-----100psi
chamber volume--------------45 ci (approx.)
barrel volume------------------25 ci (approx.)
c/b ratio--------------------------1.8 to 1(approx.)
firing valve----------------------pneumatically actuated sprinkler valve (a "modded sprinkler" valve)
pilot valve-----------------------blow gun valve
fill valve--------------------------female quick disconnect
fire rate--------------------------single shot, bolt action
caliber---------------------------25MM ( one inch)
projectile velocity-------------unknown (coming soon)
effective range----------------unknown (coming soon)
maximum range-------------unknown (coming soon)
optics---------------------------3-9X40MM rifle scope
primary material used------PVC pipe
I WOULD SUGGEST YOU DO SOME RESEARCH BEFORE UNDER TAKING THIS PROJECT, LOOK INTO THE DIFFERENT TYPES OF PIPE AND THERE RATINGS, HOW TO SOLVENT WELD PVC (THIS IS A MUST), HOW TO PROPERLY DRILL AND THREAD HOLES FOR FITTINGS, THE TYPE OF CONDITIONS PVC CAN BE USED AND STORED IN. THE MAJORITY OF THIS INFORMATION IS CONTAINED WITHIN THIS INSTRUCTABLE BUT IT IS BECOMING CLEAR THAT MANY OF YOU ARE NOT READING ALL OF IT. I HAVE ONE FINAL SUGGESTION BUILT A BASIC PNEUMATIC OR COMBUSTION FIRST IF A BASIC CANNON FAILS IT WILL BE LESS DANGEROUS
PS - DON'T ATTEMPT THIS AT ALL IF YOU HAVE NO COMMON SENSE OR A LOW
well before we begin i must state a few things...
-PVC can only be used at half or less than half the pressure rating stamped on the pipe when pressurized gases are used in the pipe
-i would suggest never pressurizing this cannon above 150 psi, remember its only plastic
-never store any type of PVC pneumatic with pressure still in it
-always allow a full 24hours for PVC glue to dry before pressurizing
-when building pneumatics always use metal or PVC pipe (never ABS)
-PVC is shock sensitive meaning if its dropped on a hard its very likely it will be damaged and it would be very dangerous to pressurize after damaged
-PVC becomes very brittle below 32 degrees (Fahrenheit) and is very likely to explode if pressured in such conditions
-when building pneumatics pressure rated pipe should always be used (none of that cell core or DWV crap)
-the most important part of any pneumatic are the PVC welds AND I HIGHLY SUGGEST YOU READ THIS TUTORIAL before you even think about starting this.
-when you are dealing with high velocity projectiles always remember you safety glasses
-always be sure of your back stop when shooting any form of rifle, pistol, gun, bow.... anything that can fire some vague form of projectile
-and use common sense!
-do not use un-regulated HPA or CO2 in a PVC cannon ever they are stored at to high of pressures to be safe in PVC, but if you have a properly regulated setup they can be used ( if you lower the pressure to about 100psi)
Now onto the good part...
this is my entry for the launch it challenge, it is a 25MM Pneumatic Cannon. it has 2.5 foot long one inch diameter barrel with a custom bolt action mechinism, of course we have the 3-9X40 sniper scope, and a 1" modified sprinkler valve as the primary firing valve.
The Video...
Video
invalid movie: http://youtube.com
remember always wear safety goggles, you never know where or when something will ricochet especially when its traveling at 300+FPS
Fun Fact: PVC shards can't be picked up by X-Rays (this is a safety tip! don't rush or you'll get a PVC shard in you and you probably wont get it out. im not saying you should sneak one of these into your luggage and go threw airport security. it would be way to big any way)
better video coming soon
If you like this instructable please register and vote for it in the launch it challenge (by click the plus icon next to the title)
DETAILED SPECS
power source------------------compressed air
power source pressure-----100psi
chamber volume--------------45 ci (approx.)
barrel volume------------------25 ci (approx.)
c/b ratio--------------------------1.8 to 1(approx.)
firing valve----------------------pneumatically actuated sprinkler valve (a "modded sprinkler" valve)
pilot valve-----------------------blow gun valve
fill valve--------------------------female quick disconnect
fire rate--------------------------single shot, bolt action
caliber---------------------------25MM ( one inch)
projectile velocity-------------unknown (coming soon)
effective range----------------unknown (coming soon)
maximum range-------------unknown (coming soon)
optics---------------------------3-9X40MM rifle scope
primary material used------PVC pipe
I WOULD SUGGEST YOU DO SOME RESEARCH BEFORE UNDER TAKING THIS PROJECT, LOOK INTO THE DIFFERENT TYPES OF PIPE AND THERE RATINGS, HOW TO SOLVENT WELD PVC (THIS IS A MUST), HOW TO PROPERLY DRILL AND THREAD HOLES FOR FITTINGS, THE TYPE OF CONDITIONS PVC CAN BE USED AND STORED IN. THE MAJORITY OF THIS INFORMATION IS CONTAINED WITHIN THIS INSTRUCTABLE BUT IT IS BECOMING CLEAR THAT MANY OF YOU ARE NOT READING ALL OF IT. I HAVE ONE FINAL SUGGESTION BUILT A BASIC PNEUMATIC OR COMBUSTION FIRST IF A BASIC CANNON FAILS IT WILL BE LESS DANGEROUS
PS - DON'T ATTEMPT THIS AT ALL IF YOU HAVE NO COMMON SENSE OR A LOW
Nenhum comentário:
Postar um comentário